How-To: ZL1 1LE Front End Conversion // GM OEM 1LE Parts

This video will cover how to remove the front bumper from your 6th Gen Camaro ZL1, and replace the existing splitter, upper and lower grill, and side intakes with the GM OEM 1LE pieces from Wildhammer Motorsports. We will also add the 1LE dive planes to complete the ZL1 1LE look. Here are all of the OEM GM part numbers, and links to get everything:

GM ZL1 1LE Part Numbers:
84712513 - Rear Wing Spoiler
84375811 - Lower Grille
84718397 - Upper Grille
84335746 - Front Splitter
84277492 - Left Air Inlet
84277493 - Right Air Inlet
23329726 - Left Dive Plane
23329727 - Right Dive Plane
23329728 - Left Splitter Deflector
23329729 - Right Splitter Deflector
11547341 - Mounting Clips x12
11609456 - Splitter Screw x6
11610157 - Splitter Nut x6

Affiliate Links:
GM Camaro ZL1 1LE Splitter, Grille & Dive Plane Kit - Wildhammer Motorsports - Fits 2017-2024:
https://bit.ly/ZL11LEConv

Chevy Camaro ZL1 1LE Full Carbon Fiber 1pc Rear Spoiler - Fits 2016-2024:
https://bit.ly/3PmA3uu

Milwaukee 1/2” Drive Socket & Wrench Set:
https://amzn.to/430BKlz

Milwaukee 3/8” & 1/4” Drive Socket & Wrench Set:
https://amzn.to/3Mztv98

10mm Swivel Wrench:
https://amzn.to/45QFas4

Magnetic Pickup & Tray Tool Set:
https://amzn.to/3P6sJlv

Panel Removal Tool Set // 200PC:
https://amzn.to/3qZCrOo

Plastic Blade Trim Removal Tool:
https://amzn.to/3EoHomX

LED Side Markers:
https://amzn.to/42RBzJ2

Lift Pads:
https://amzn.to/3s3FwtT

ZL1 Addons Premium Magpuck:
https://tinyurl.com/bd9kp5cm

Rotofab CAI for Camaro w/ LT4 V8:
https://amzn.to/43jSmW8

Rotofab CAI for Camaro w/ LT1 V8:
https://amzn.to/3ZRchbT

Corsa Extreme Axle Back Camaro V8:
https://amzn.to/3BSxdG3

Corsa Carbon Fiber CAI for ZL1:
https://tinyurl.com/wr8s4rx8

Milwaukee Fastback Blade:
https://amzn.to/48cs2Q8

Bosch 7/64th Drill Bit:
https://amzn.to/489FwfB

Milwaukee M12 3/8” Ratchet:
https://amzn.to/3Ezznvo

Milwaukee M12 1/4” Screw Gun:
https://amzn.to/3rcVN2G

Chapters:
0:00 - Intro
0:32 - Tools Needed
3:05 - Overview
3:50 - OEM Part Numbers // Links in Description
4:18 - Fender Well Liner Removal // Bolt Locations
5:28 - Access Panel Removal // Makes Things Easier but NOT Required
6:24 - Removing the Factory Bolts Under the Car
7:30 - Removing the Center Bottom Mounted Radiator Cover
7:47 - Bumper Bolt Location at the Sides // 7mm & 10mm
9:12 - Bumper Bolt Location at the Front // 7mm
9:30 - Removing the Bolts Under the Hood // T15 & Push Pins
10:10 - Pulling the Front Bumper Off
11:10 - Bumper Harness under Driver Headlight
11:32 - Front Bumper Off // Clean Your Radiators
12:10 - Removing the Crash Bar Absorption Styrofoam
14:40 - Removing the ZL1 Upper Grille
18:00 - Saggy Bumper // Foam Block
18:27 - ZL1 vs ZL1 1LE Upper Grille Differences
19:08 - Installing the ZL1 1LE Upper Grille // MOST Difficult Part
20:08 - Removing the Lower ZL1 Grille
22:16 - ZL1 vs ZL1 1LE Lower Grille Differences
23:40 - Installing the ZL1 1LE Lower Grille
25:00 - Removing the Daytime Running Lamps // DRL
25:50 - Tie Up the DRL Harnesses
26:23 - Removing the ZL1 Side Air Intakes // Second MOST Difficult Part
28:20 - Cutting the ZL1 Bumper // Splitter & Dive Plane Cut Locations
30:52 - Test Fitting the Dive Planes
31:35 - Installing the ZL1 1LE Side Air Intakes
33:30 - 1LE Dive Plane Installation
35:22 - Removing the ZL1 Splitter
35:50 - Installing the 1LE Splitter
37:55 - Installing the 1LE Splitter End Plates
39:45 - Reinstalling the Crash Bar Absorption Styrofoam
40:30 - Securing the DRL Harness to the 1LE Side Intake
41:40 - Reinstalling the Assembled Bumper // Reconnect the Harness!
42:20 - Outro // Beauty Shots

These are affiliate links to the products. I make a small commission on anything purchased from my links.

**Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use of the information I share in my videos. (FollowMyLine17) assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not (FollowMyLine17) or any business affiliated to (FollowMyLine17).**