In this video, I share 11 3D Printing Slicer settings that you never knew you needed. This video is brought to you by PCBWay, your one-stop-shop for PCB prototypes and assemblies. Visit them at https://jle.vi/pcbway

Knowing the ins and outs of your Slicer of choice can mean stronger 3D prints, faster print times, less time spent in CAD customizing your models and much, much more.

In this video I'm going to share a handful of lesser known Slicer settings that will help you take your 3D prints to the next level. I'll be demonstrating in "Orca Slicer," which is a fork of Bambu Studio, which is a fork of PrusaSlicer, but it should be the same in Cura. And, it will work with ANY 3D Printer (FDM, not resin) that you choose to use.

Enjoy, and comment/subscribe if you do!

💬 JOIN MY DISCORD: https://jle.vi/tnl-discord

🎁 EXCLUSIVE CONTENT ON PATREON:   / thenextlayer  

🎥 IN THIS VIDEO: 🎥
00:00 Introduction
01:38 Slicer Setting No. 1: Solid Infill Modifiers
02:18 Slicer Setting No. 2: Modifier Areas
02:56 Slicer Setting No. 3: Negative Volume Modifiers
03:40 Slicer Setting No. 4: Close Holes Slicing Mode
04:23 Slicer Setting No. 5: Hole X-Y Compensation
05:54 Slicer Setting No. 6: Combine Infill Layers
06:25 Slicer Setting No. 7: Variable Layer Height
07:09 Slicer Setting No. 8: Ironing
07:55 Slicer Setting No. 9: Cut Feature
08:22 Slicer Setting No. 10: Complete Individual Objects
09:21 Slicer Setting No. 11: Per-Object Settings
10:41 Conclusion

🛒 RECOMMENDED GEAR: 🛒
📍 Complete list of 3D Printing accessories: https://kit.co/jlevi/3d-printing
📍 Complete list of my videography gear: https://kit.co/jlevi/content-creation
📍 My favorite 3D printing filament: https://jle.vi/polymaker
📍 My favorite 3D printer right now: https://jle.vi/voronkits | https://jle.vi/bambu (supports 3D Print General, who’s channel was deleted)
📍 My favorite BUDGET 3D printer right now: https://jle.vi/sovol
📍 Check out the official TNL merch: https://shop.thenextlayer.com/
📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: https://jle.vi/links

🔗 OTHER LINKS 🔗
👉 Check out Orca Slicer (which I like more than Prusa Slicer, Cura, or even Bambu Studio): https://github.com/SoftFever/OrcaSlicer
👉 Check out my previous video where I showed my Honeycomb Storage Wall:    • Is This 3D Printed Tool Wall The Next...  


❤️ LOVED THIS VIDEO? ❤️
▶️ Subscribe to the channel
▶️ Watch my other videos:    / @thenextlayer  
🔔 Turn on Notifications
🎁 Support me on Patreon:   / thenextlayer  
🎁 Send a “Super Thanks” (Tip)
🛒 Use my affiliate links for your 3D printing or videography needs: https://kit.co/jlevi
💬 Join My Discord: https://jle.vi/tnl-discord
✍️ Write a comment below!
👍🏿 Like this video


#3dprinting #3dprinted #3dprinter